Technology of laying gypsum tiles with your own hands

Gypsum tiles must be laid correctly, as not just the aesthetic look of cosmetic facing, but also the service quality of this

substance will rely on the technologies of job. The product is also universal, and it can be attached to plaster, concrete, brick

or gypsum board sheets, and provided that the top layer of the base is and has no defects.

If the defects of this base are significant, it should be completely treated with primer, then a cement mortar is made, which

matches all of the cracks. Then the surface should be primed and dried. Primer therapy is essential to improve the bond between

the tile and the walls. In this case, its composition should pick a special, comprising components that prevent the appearance of

fungus and mould.

In the modern interior of the rooms most often used gypsum tiles, even imitating natural stone or brick. To execute cosmetic

finishing your self, it’s necessary first of all to choose a strategy of tile positioning and prepare a remedy. It is important to

look closely at the opposite side of this material. If its surface has an embossed surface, then the glue should be put using an

even trowel, also if it is even, then using a notched one.

The technologies of the job is as follows:

* A thin coating of glue mortar is applied to the pre-prepared wall. It is distributed over the bottom so that it is likely to

put 4-5 tiles. Decorative cladding can be placed either on plasterboard, and on putty.

* Glue the back side of these tiles with adhesive.

* Plaster elements are pressed against the walls and their location is adjusted. To align with the seams, it is suggested to use


* Finishing is carried out in rows, each of which ought to be shifted by half a tile. Facing is completed into the corners of

this space, and then immediately get rid of any residual mortar in the joints.

Drying the walls requires no more than a day also needs a continuous humidity and temperature inside the room. The last stage in

the laying of gypsum tiles is that their decoration. To do this, the joints between these components are full of a particular

solution, the shade of which matches the brick.

Cosmetic fake of brickwork around the walls is carried out in the following manners:

* Cutting the surface of the pits of masonry with a bolt cutter along with your own hands;

* placing of tiles beneath the brick:

* mimicking the format and colour of the side of one brick;

* Imitating a fragment of brickwork of many bricks.

The perfect approach to decorate”under the brick” is really the one that allows you to create a usable coating together with the

most look of its resemblance to natural masonry. All 3 ways to carry out this kind of finishing functions meet the prerequisites,

however, the cutting of joints using a bolt will be labor-intensive and the formation of large quantities of dust, and so let’s

consider more typical manners.

The old finish is removed from the walls, and the surface, if needed, is leveled to eliminate the requirement to paste plaster

onto a thick layer of adhesive.

Combining such cladding with other kinds of interior finishes may be both systematic and performed without any apparent

consistency, chaotically, with fake of signs of aging.

With the help of cosmetic gypsum tiles it’s possible to mimic a large number of textures.

A lot of textures can be imitated with the support of cosmetic gypsum tiles.

The wall on which it’s to be installed should have the following characteristics:

* Hardness and durability of the outside;

* The absence of irregular locations and sharp sections;

* no deformations.

Cosmetic tiles in the interior of this kitchen

Walls are made from a variety of substances, so let’s break down the principles of installment.

When dealing with concrete, there’ll not be any huge problems. It is just necessary to take into consideration the porosity of

this material. Concrete, which has practically no pronounced pores, ought to be treated with a good primer.

Mounting gypsum tiles concrete

Before starting work on the setup of gypsum tiles onto the walls, it’s well worth assessing the strength of the surface. When the

plaster does not drop off the wall and in exactly the identical time holds nicely, it is possible to simply paint it with primer.

Mount the tiles on the painted concrete should not. The surface should be scratched, ensuring to misfire, then it should be

grouted and covered with a layer of plaster.

Hammad Administrator
Sorry! The Author has not filled his profile.
Hammad Administrator
Sorry! The Author has not filled his profile.
Latest Posts

Comment here